Showing posts with label design. Show all posts
Showing posts with label design. Show all posts

Thursday, February 08, 2007

The Cemforce Slab

The Cemforce slab is made up of the same sandwich material used for the panels, but with some steel reinforcement cast in the bottom half of the mould, to increase the bending strength of the slab. Wicus, one of the owners of Cemforce, carried out a pretty impressive test on the slab, which is only 65mm thick, by supporting the slab on two supports and slowly adding bags of cement across the middle. With 900kg of cement on the slab, it only deflected by 5mm!

In rural areas, when a toilet pit fills up, they are rarely emptied, since this requires a tanker to come and suck the c##p up, which costs money. Instead people tend to dig a new pit and install a whole new toilet. Cemforce had designed a cool little buggy thing which is bolted together around the edge of the slab. The frame and the slab is then lifted up using a big lever, and wheels are fitted onto little brackets at the corner of the buggy. It can then be wheeled over the new pit and lowered into position, and the buggy frame removed. This way people don’t have to buy a new toilet every time the pit fills up… (as long as they can call up cemforce to get hold of one of those buggies)


Monday, December 04, 2006

Strengthening

I was in touch with the producer of my cement and was sent some lovely Cement performance curves!!
Buildcrete curve (general purpose cement)
Powercrete curve (a slightly quicker-setting cement)
Duracast curve (an even quicker setting cement)

These little beauties opened my eyes a little.

I knew that less water=stronger cement (see earlier post) but I didn’t realise the extent to which this mattered. For every 1 L of cement, I’m putting in 0.8L of water, so that its runny enough to work with. This is because I’m using fine sand, as well as coarse sand. This fine stuff is good because it fills voids between the coarser sand, but is bad because it is very thirsty; you need a lot of water when you use it..

So… I’m gonna reduce the fine sand content a bit. Although in one respect it will make the concrete panels weaker, I think this will be more than outweighed by the benefit of having to use less water.

Fingers Crossed!

Time to Raid the Bottle Bank...

My panels are floppy. Its sad but true. They need to be stiffer!
I visited a Textile Concrete factory where they use Textile Concrete to make all sorts of pretty concrete products, including doors, wall panels, and even artwork and sculptures. The textile gives the concrete enough extra strength to be able to sculpt the cement mortar, do you ever remember making papier mache sculptures out of wire mesh? It’s a bit like that.
They were understandably reluctant to reveal their commercial secrets, but we did find that they’d used Glass Fibre mesh to strengthen their Textile Concrete panels.

Since then I’ve got hold of a roll of Glass Fibre mesh from Durban. Fingers crossed it’ll help with the stiffness.

Also I thought hey – woven glass fibre mesh might have some recycled glass in it right? Well apparently not. The mesh manufacturers put me onto the Glass Suppliers. A very helpful bloke told me that their fibreglass insulation is made up of glass fibre with up to 40% recycled content, but fibreglass used for reinforcing mesh must be of a higher quality (no organic material) and so is made using virgin glass. Bummer.

Making Cement More Green and Fluffy

I like recycling, I think it’s a great idea. So I thought that I should look into how I could use recycled materials in my work.

I’ve heard lots of people mention Fly Ash as an additive to cement. Fly ash, (AKA Pulverised Fuel Ash or Blast Furnace Slag) is the stuff left over after burning coal. You can use it as a replacement for some of the Cement you use for concrete. Great eh? I spoke to a big cement producer in South Africa and they told me that the cement I was using already had 20% Fly Ash in it (apparently they caught onto this quite a long time ago) and soon they’d be producing cement with 40% Fly Ash in it. Hurrah! I was being recycling(ish) without even knowing it!

Tuesday, October 24, 2006

Textile Concrete Panels

For the wall panels, roof, door and pit lining I'm going to be using thin panels of Textile Concrete. I'd never come across it before but its basically plastic-fibre reinforced concrete. You make it by pouring alternating layers of a runny cement slurry and plastic textile, as you can see below:
If you want concrete panels, you used to be able to get asbestos fibre-reinforced panels, but since asbestos rips your lungs to shreds if you inhale the fibres accidentally, its been banned in most countries, including South Africa. As a replacement you can get cellulose fibre reinforced concrete panels, which I would say is a bit more eco-friendly as the cellulose is from plant pulp. Unfortunately these materials are fairly brittle, and so crack easily.

Textile Concrete, on the other hand can flex quite a lot without cracking (it is ductile rather than brittle). This (I think!) is because the cement slurry has a latex-based chemical added to it, which I guess slows down the rate at which cracks propagating through the panel.
Which makes me think, maybe if you got cellulose panels and added the additive, then you would get eco-friendly, flexible concrete panels? (maybe?) Anyway

Over the past couple of weeks I've been playing around with different types and proportions of sand (some from the hardware store, and some from a riverbank down the road) which is mixed with cement, water and a latex-based additive. I've been leaving them for a day and then putting them in a tank of water for a few days to cure, and I've been experimenting with different curing times.

Monday, October 23, 2006

Introducing... The VIP latrine!

Regular Pit Latrines, aka Long Drops are pretty much the most basic form of toilets, and are what is used by the vast majority of the world's population. (I can't prove that, but I reckon its probably true!) They are just holes in the ground with a few planks of wood or a slab of concrete over the top which you sit on when you are doing your thing. There is usually a lid over the hole, to stop flies getting in and the smell getting out.

Flies are a big problem because they mess around in the faeces, come back out of the pit and then go and sit on some food, or a person, spreading any bacteria which they might have picked up from the faeces.

In order to reduce the smell, and stop a flood of flies leaving the pit every time you take the lid off the Regular Pit Latrine, some bright spark came up with the Ventilated Improved Pit (VIP) Latrine in the 70's . The difference is the addition of a vent pipe.
Flies which are drawn by smell into the pit are attracted up the vent pipe by the brightness of daylight at the top it, but cannot escape because of the screen (unless they are clever enough to fly back down the pipe and reconsider their choice of escape holes). Wind passing over the vent pipe causes an updraught, removing any smell and helping to draw flies up to the top of the pipe. So now you don't get facaes-covered flies coming out of the toilet. Hurrah!

Here's a pic of a lady called Rosemary, sporting her brand new, and rather pretty, VIP Latrine!

For budding toilet-geeks, check out the myriad toilet options in WaterAid's technology notes.

Tuesday, October 17, 2006

The Slab

The Slab sits over the Pit. Around Jozini they tend to be made out of a 10cm thick slab of reinforced concrete with some steel rods inside them to provide additional strength. To cast them, wet concrete is poured into a wooden mould which sits over the pit, and when the concrete sets, the mould is removed.

But... I want to avoid the trouble of pouring concrete in someones back garden out in the rural areas. I want to be able to turn up at the customers with the whole loo, dig a pit, put it all in place and then go home!

So, I was looking for a way to cast the Slab in a factory, and make it light enough so that it can be stuck in the back of a buckie/ute/4x4/what Jo Mangel was always driving in Neighbours, then carried it into place over the pit.

Then I stumbled upon the SanPlat website. This had instructions for building a Dome-shaped slab which allows you to have a much thinner slab (4cm) and no steel reinforcement! And here's why...
Concrete is strong when squashed (compression) but pretty useless when stretched (tension), If the Slab was flat, then the top half of the Slab would be in compression, but the bottom half of the Slab would be in tension :-( so you would need to cast steel rods into the bottom half of the flat slab for additional strength (steel is good in both tension AND compression).

With our Dome Slab, by virtue of its shape, both the top half and the bottom half the Slab is in compression so you don't need the steel. (Trust me on this one) Hurrah for domes, and the same goes for arches too!

So, the Dome shape reduces the weight of the slab to about 200kg. Which is still pretty heavy eh? But, if one person lift 50kg then we're talking four people carrying the slab, which seems ok.

Tuesday, October 10, 2006

The Pit

Ok, so lets start aat the bottom..(hahaha the first of many lame jokes) the pit is where the faeces goes, and the size of this pit can be whatever you want it to be. A sensible figure for how much faeces people produce in a year is about 65L. If we take an average 6-person family in Kwa-zulu Natal, and we want the pit to last, say 6 years, then you need a pit that is...65x6x6 = 2340L=2.34m3.

Now you don't really want to dig too dep a hole, as there is a danger that it might collapse when you are digging it, so I'll specify a depth of 1.6m. This means that the pit has dimensions of 1.2m x1.2m and 1.6m deep.

The sides of the pit can be lined with bricks to stop all the earth filling the pit in. How strong this lining is depends on the soil in which the hole is dug. For unstable, sandy soil the walls of the pit you are digging will tend to collapse easily, so you want a stronger lining whilst for more stable, rocky soil you want a weaker lining, or perhaps even no lining at all.

Irrespective of this, the bottom of the pit is unlined, as you want the liqiuds to soak away into the soil.

For the loo factory loo, we will use Textile Concrete panels for the lining. Since they do not need to be watertight, I'll try to make the panels interlocking, so that the pit lining is easy to put together. Of course it might be a good idea to offer customers the choice of not having a pit lining, if it turns out that the soil in the place where they dig the pit is sufficiently stable. In really rocky soil, on the other hand, it might be easier to to drill a narrow, deep hole using a hand-auger, if one is available.